Series of Encoders. Features · Operating voltage: V~12V · Built-in oscillator needs only 5% resistor · Low power and high noise immunity CMOS · Easy. HOLTEK. Manufacturer: HOLTEK HOLTEK. Manufacturer Part No: HT 18DIPLF. Order Code: Technical Datasheet: HTDIPLF Datasheet. HT datasheet, HT pdf, HT data sheet, datasheet, data sheet, pdf, Holtek Semiconductor, Series of Encoders.
|Published (Last):||17 September 2012|
|PDF File Size:||19.20 Mb|
|ePub File Size:||1.59 Mb|
|Price:||Free* [*Free Regsitration Required]|
Taipei Sales Office 4F-2, No. Regards, Tayyab R, National Instruments. You can look at the tutorial in the attached link to create the component. Currently, Multisim doesn’t have anything resembling these components for me to design the schematics for our project report and I was wondering if it’s possible at all to create custom prz files to import for these components.
You will need to get the spice model for the components which can usually be found at the manufacturer’s website.
HT datasheet, Pinout ,application circuits HT// — 3^12 Series Of Encoders
All other trademarks are the property of their respective owners. Copy your embed code and put on your site: Message 4 of 4.
In Multisim, there is a model maker. Low power and high noise immunity CMOS. Ht60144 Voltage The recommended oscillator frequency is f Rev. Functional operation of this device at other conditions beyond those listed in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability. Can a spice model be created by inputting data from the datasheet? I’ve tried using Google and going directly to the manufacturer websites.
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type. Message 2 of 4. The address pins are usually preset so as to transmit data codes with their own particular security codes by the DIP switches or PCB wiring, while data is selected using push button or electronic switches. The information appearing in this Data Catasheet is believed to be accurate at the time of publication.
Selection Table Function Address No. A B C 14 Rev.
Multisim and Ultiboard
Holtek reserves the right to alter its products without prior notification. Holtek reserves the right to alter its products without prior notification. TE is the transmission enable pin of the HT Holtek s products are not authorized for use as critical components in life support devices or systems.
Easy interface with an RF or an infrared transmission. If the trigger signal is not applied, the chip only consumes a standby current which is less than 1 A for V The address pins are usually preset transmit data codes with their own particular security codes by the DIP switches or PCB wiring, while data is selected using push button or electronic switches Is it possible to create custom prz files?
They are otherwise set floating internally. It appears that Holtek and RSR don’t have spice models for any of their products. For the most up-to-date information, please visit our web site at http: These are stress ratings only.
Holtek Semiconductor Inc. HT Series Datasheets. HT, HT, HT Datasheet.
That link would be very helpful if I could actually get spice models for any of these components. They are capable of encoding 12 bits of information which consists of N address bits and N data bits. The component you want to simulate is a very complex component and you will not be able to create the spice model for it using the model maker.
Once the transmission enable returns high the encoder output completes its final cycle and then stops as shown below. Any help is greatly appreciated They are capable of encod.
HT6010/6012/6014 — 3^12 Series Of Encoders
Most Active Software Boards: Download datasheet Kb Share this page. Elcodis is a trademark of Elcodis Dtasheet Ltd. It is possible to create custom components in Multisim. The applications mentioned herein are used solely for the purpose of illustration and Holtek makes no warranty or representation that such applications will be suitable without further modification, nor recommends the use of its products for application that may present a risk to human life due to malfunction or otherwise.
I’m currently a student at DeVry working on one of darasheet class projects. Once the transmission enable returns high the encoder output completes its final cycle and then stops as shown below For the most up-to-date information, please visit our web site at http: I am not exactly sure why you would need to create a customer prz file.
Message 1 of 4. However, Holtek assumes no responsibility arising from the use of the specifications described. TE is the transmission enable of the HT Full Lead Packages Fig2. Generally, you would need to use LabVIEW to create such an instrument and then try to use it in Multisim but again it is not a simple task.
Message 3 of 4. When you are going throught the process of creating a new component, you will see on the window where you need to enter the spice model but the model maker has support only for a few basic components for which you can enter the values from the datasheet.